2002 NISSAN ALTIMA RECALL - #03V084000
RECALL FOR ENGINE AND ENGINE COOLING : EXHAUST SYSTEM : MANIFOLD/HEADER/MUFFLER/TAIL PIPE
ON CERTAIN VEHICLES EQUIPPED WITH THE 2.5 LITER ENGINE, THE EXHAUST PIPE HANGER PIN MAY CATCH DEBRIS FROM THE ROAD THAT COULD BE IGNITED BY CONTACT WITH THE MAIN CATALYST. ALSO ON 2002 ALTIMA AND SENTRA VEHICLES, CERTAIN ENGINE OPERATING CONDITIONS MAY CAUSE THE PRE-CATALYST TO OVERHEAT AND DAMAGE THE CATALYST SUBSTRATE.
Information provided by the
National Highway Traffic Safety Administration.
•
Send to a friend
•
Hide Form
Recall Details
| Vehicle |
2002 NISSAN ALTIMA |
|
| Manufacturer |
NISSAN NORTH AMERICA, INC. |
| Manufactured between |
8/1/2001 - 6/23/2003 |
| Recalled on |
3/18/2003 |
| Influenced by |
OFFICE OF DEFECTS INVESTIGATION |
| Owners Notified on |
7/28/2003 |
| # Affected |
338,000 |
| Recalled for |
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE |
|
|
| Description |
ON CERTAIN VEHICLES EQUIPPED WITH THE 2.5 LITER ENGINE, THE EXHAUST PIPE HANGER PIN MAY CATCH DEBRIS FROM THE ROAD THAT COULD BE IGNITED BY CONTACT WITH THE MAIN CATALYST. ALSO ON 2002 ALTIMA AND SENTRA VEHICLES, CERTAIN ENGINE OPERATING CONDITIONS MAY CAUSE THE PRE-CATALYST TO OVERHEAT AND DAMAGE THE CATALYST SUBSTRATE. |
| Consequences |
EITHER OF THESE TWO CONDITIONS COULD RESULT IN A FIRE. |
| Corrective action |
DEALERS WILL REMOVE THE PROTRUDING PORTION OF THE EXHAUST PIPE HANGER PIN. IN ADDITION TO THE CORRECTIVE ACTION, IN ORDER TO REDUCE THE RISK OF FIRE IN THE EVENT OF POOR OR IMPROPER MAINTENANCE THAT COULD RESULT IN OIL SPILLAGE, HEAT SHIELD(S) WILL BE INSTALLED ON THE PRE-CATALYST AND EXHAUST TUBE. OWNER NOTIFICATION BEGAN ON JULY 28, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261. NISSAN RECALL NOS. R3007, R3014, R3015, R3016, R3017. ALSO ON 2002 ALTIMA AND SENTRA VEHICLES, CERTAIN ENGINE OPERATING CONDITIONS MAY CAUSE THE PRE-CATALYST TO OVERHEAT AND DAMAGE THE CATALYST SUBSTRATE. IF SUBSTRATE PARTICLES ENTER THE COMBUSTION CHAMBER, THEY COULD SCORE THE CYLINDER WALLS, RESULTING IN INCREASED OIL CONSUMPTION. IF THE ENGINE OIL LEVEL IS NOT CHECKED ON A PERIODIC BASIS AND DROPS BELOW THE LOW LEVEL, AND THE DRIVER CONTINUES TO OPERATE THE VEHICLE IGNORING NOTICEABLE ENGINE NOISE, ENGINE DAMAGE MAY OCCUR WHICH COULD RESULT IN A FIRE. THE PRE-CATALYST WILL BE TESTED TO ENSURE IT IS WORKING PROPERLY AND REPLACED IF NECESSARY. IF DAMAGE IS FOUND INSIDE THE PRE-CATALYST, IT WILL BE NECESSARY TO REPLACE THE ENGINE. |
| Notes |
CUSTOMERS CAN ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236). |
| See also |
2002 NISSAN ALTIMA Recall for AIR BAGS, FRONTAL, DRIVER SIDE, INFLATOR MODULE
2002 NISSAN ALTIMA Recall for FUEL SYSTEM, GASOLINE, STORAGE, TANK ASSEMBLY
2002 NISSAN ALTIMA Recall for ENGINE AND ENGINE COOLING
2002 NISSAN ALTIMA Recall for ENGINE AND ENGINE COOLING
|
| Technical Service Bulletins |
May 10, 2021 - 010000 STEERING
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut P
May 10, 2021 - 010000 STEERING
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into
May 10, 2021 - 020000 SUSPENSION
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition wh
May 10, 2021 - 020000 SUSPENSION
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into
May 10, 2021 - 030000 BRAKES (PWS)
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut P
View all Technical Service Bulletins
|
|