|
Problem: CERTAIN FREIGHTLINER TRUCKS AND THOMAS SCHOOL BUSES EQUIPPED WITH HOLLAND/NEWAY AIR SUSPENSION SYSTEMS, A TRANSVERSE BEAM CASTING MAY FRACTURE UNDER NORMAL LOADS. IF A CASTING BREAKS WHEN THE VEHICLE IS TRAVELING ON A ROADWAY THERE IS THE POTENTIAL FOR PIECES OF THE CASTING TO BECOME PROJECTILES AND THE SUSPENSION'S TRANSVERSE BEAM MAY DROP DOWN LOW ENOUGH TO CONTACT THE ROAD SURFACE. Recall Details
Problem: CERTAIN MY 2000-2003 FREIGHTLINER, THOMAS MVP SCHOOL BUS AND WESTERN STARS TRUCKS MANUFACTURED BETWEEN NOVEMBER 19, 2000, AND MARCH 30, 2005, AND EQUIPPED WITH WEBASTO COOLANT HEATERS, MODEL DBW 2010, ASSEMBLED WITH WEBASTO BURNER TUBES, P/N 303046/26533A. THE STAINLESS STEEL BURNER TUBE IS MADE OUT OF A MATERIAL THAT IS NOT TO SPECIFICATION AND COULD FAIL PREMATURELY. Recall Details
Problem: CERTAIN MY 2000-2003 FREIGHTLINER, THOMAS MVP SCHOOL BUS AND WESTERN STARS TRUCKS MANUFACTURED BETWEEN NOVEMBER 19, 2000, AND MARCH 30, 2005, AND EQUIPPED WITH WEBASTO COOLANT HEATERS, MODEL DBW 2010, ASSEMBLED WITH WEBASTO BURNER TUBES, P/N 303046/26533A. THE STAINLESS STEEL BURNER TUBE IS MADE OUT OF A MATERIAL THAT IS NOT TO SPECIFICATION AND COULD FAIL PREMATURELY. Recall Details
Problem: CERTAIN MY 2000-2003 FREIGHTLINER, THOMAS MVP SCHOOL BUS AND WESTERN STARS TRUCKS MANUFACTURED BETWEEN NOVEMBER 19, 2000, AND MARCH 30, 2005, AND EQUIPPED WITH WEBASTO COOLANT HEATERS, MODEL DBW 2010, ASSEMBLED WITH WEBASTO BURNER TUBES, P/N 303046/26533A. THE STAINLESS STEEL BURNER TUBE IS MADE OUT OF A MATERIAL THAT IS NOT TO SPECIFICATION AND COULD FAIL PREMATURELY. Recall Details
Problem: CERTAIN MY 2000-2003 FREIGHTLINER, THOMAS MVP SCHOOL BUS AND WESTERN STARS TRUCKS MANUFACTURED BETWEEN NOVEMBER 19, 2000, AND MARCH 30, 2005, AND EQUIPPED WITH WEBASTO COOLANT HEATERS, MODEL DBW 2010, ASSEMBLED WITH WEBASTO BURNER TUBES, P/N 303046/26533A. THE STAINLESS STEEL BURNER TUBE IS MADE OUT OF A MATERIAL THAT IS NOT TO SPECIFICATION AND COULD FAIL PREMATURELY. Recall Details
Problem: VEHICLE DESCRIPTION: TRUCK/TRAILERS EQUIPPED WITH A HYDRAULIC PARKING BRAKE. A CASTING ERROR IN THE HYDRAULIC PARKING BRAKE RELAY VALVE CAUSES EXCESSIVE PRESSURE IN THE BRAKE SYSTEM WHICH CAN RESULT IN A HYDRAULIC HOSE SEPARATION. Recall Details
Problem: THE FOUR FASTENERS THAT RETAIN THE OUTPUT SHAFT BEARING TO THE STEERING COLUMN TILT/TELESCOPING MECHANISM WAS NOT TORQUED PROPERLY. Recall Details
Problem: THE FOUR FASTENERS THAT RETAIN THE OUTPUT SHAFT BEARING TO THE STEERING COLUMN TILT/TELESCOPING MECHANISM WAS NOT TORQUED PROPERLY. Recall Details
Problem: THE EQUALIZING BEAM SHAFT OF THE TANDEM AXLE SUSPENSION WERE MANUFACTURED FROM AS-ROLLED SAE4140 STEEL RATHER THAN THE SPECIFIED ANNEALED SAE4140. THESE SHAFTS CAN FRACTURE INSIDE THE BEAM AT THE TOE OF THE WELD. Recall Details
Problem: THE EQUALIZING BEAM SHAFT OF THE TANDEM AXLE SUSPENSION WERE MANUFACTURED FROM AS-ROLLED SAE4140 STEEL RATHER THAN THE SPECIFIED ANNEALED SAE4140. THESE SHAFTS CAN FRACTURE INSIDE THE BEAM AT THE TOE OF THE WELD. Recall Details
Problem: THE FOUR FASTENERS THAT RETAIN THE OUTPUT SHAFT BEARING TO THE STEERING COLUMN TILT/TELESCOPING MECHANISM WAS NOT TORQUED PROPERLY. Recall Details
Problem: THE SPRING BRAKE CHAMBERS MOUNTED ON TAG AXLES WITH MOUNTING STUDS ALIGNED HORIZONTALLY INSTEAD OF VERTICALLY CAN RESULT IN FRACTURE OF THE BRAKE CHAMBER HOUSING BASE WHICH LIMITS THE APPLICATION OF SERVICE BRAKES ON THE AFFECTED WHEEL. Recall Details
Problem: THE SPRING BRAKE CHAMBERS MOUNTED ON TAG AXLES WITH MOUNTING STUDS ALIGNED HORIZONTALLY INSTEAD OF VERTICALLY CAN RESULT IN FRACTURE OF THE BRAKE CHAMBER HOUSING BASE WHICH LIMITS THE APPLICATION OF SERVICE BRAKES ON THE AFFECTED WHEEL. Recall Details
Problem: THE EXHAUST PORT IN THE UP POSITION ALLOWS WATER TO ENTER THE AIR BRAKE SYSTEM, WHICH CAN BLOCK THE AIR BRAKE SYSTEM IN FREEZING CONDITIONS. Recall Details
Problem: WHEN THE FUEL TANKS WERE TESTED IN ACCORDANCE WITH FEDERAL MOTOR CARRIER SAFETY REGULATION 363.67, FUEL TANK CAPS AND/OR FILLER NECK WELDS LEAKED. Recall Details
Problem: THE SPRING BRAKE CHAMBERS MOUNTED ON TAG AXLES WITH MOUNTING STUDS ALIGNED HORIZONTALLY INSTEAD OF VERTICALLY CAN RESULT IN FRACTURE OF THE BRAKE CHAMBER HOUSING BASE WHICH LIMITS THE APPLICATION OF SERVICE BRAKES ON THE AFFECTED WHEEL. Recall Details
Problem: THE STEERING WHEEL HUB TAPER MAY BE LARGER THAN THE SPECIFIED TOLERANCES. Recall Details
Problem: THE SPRING BRAKE CHAMBERS MOUNTED ON TAG AXLES WITH MOUNTING STUDS ALIGNED HORIZONTALLY INSTEAD OF VERTICALLY CAN RESULT IN FRACTURE OF THE BRAKE CHAMBER HOUSING BASE WHICH LIMITS THE APPLICATION OF SERVICE BRAKES ON THE AFFECTED WHEEL. Recall Details
Problem: THE SPRING BRAKE CHAMBERS MOUNTED ON TAG AXLES WITH MOUNTING STUDS ALIGNED HORIZONTALLY INSTEAD OF VERTICALLY CAN RESULT IN FRACTURE OF THE BRAKE CHAMBER HOUSING BASE WHICH LIMITS THE APPLICATION OF SERVICE BRAKES ON THE AFFECTED WHEEL. Recall Details
Problem: WHEN SEAT BELTS ARE NOT BEING WORN, ABRADING OF THE WEBBING MAY OCCUR AT THE D-RING. Recall Details
Problem: CERTAIN STEERING GEAR PITMAN ARM PINCH BOLTS MAY BE DEFECTIVE; ALSO, TORQUING MAY HAVE BEEN ABOVE SPECIFICATION. Recall Details
Problem: THERE MAY BE EXCESSIVE TORQUING OF THE LOWER STEERING COLUMN PINCH BOLTS. Recall Details
Problem: THE SEAT INSERT MATERIAL DOES NOT MEET THE FLAMMABILITY REQUIREMENTS OF FMVSS 302. Recall Details
Problem: NUTS THAT RETAIN THE WHEEL HUBS ON THE TANDEM DRIVE AXLES MAY NOT BE PROPERLY TORQUED ON THE LEFT HAND SIDE. Recall Details
Problem: TRUCKS WILL EXPERIENCE REDUCED BRAKING AT LOW BRAKE APPLICATION PRESSURES WHEN OPERATING IN THE BOBTAIL MODE. Recall Details
Problem: THE SEAT INSERT MATERIAL DOES NOT MEET THE FLAMMABILITY REQUIREMENTS OF FMVSS 302. Recall Details
Problem: THERE MAY BE EXCESSIVE TORQUING OF THE LOWER STEERING COLUMN PINCH BOLTS. Recall Details
Problem: CERTAIN STEERING GEAR PITMAN ARM PINCH BOLTS MAY BE DEFECTIVE; ALSO, TORQUING MAY HAVE BEEN ABOVE SPECIFICATION. Recall Details
Problem: RESONATORS USED IN MANUFACTURING OF VIGIL II LIGHTBARS MAY CAUSE UNPREDICTABLE OPERATION. Recall Details
Problem: NUTS THAT RETAIN THE STEERING AND TIE ROD ARMS MAY CRACK WHILE TIGHTENING, DUE TO A DEEP BAR DEFECT. Recall Details
Problem: WHEN SEAT BELTS ARE NOT BEING WORN, ABRADING OF THE WEBBING MAY OCCUR AT THE D-RING. Recall Details
Problem: THE WELDED GUSSETT SUPPORTING THE LOWER FUEL TANK STEP IS OF INSUFFICIENT STRENGTH. Recall Details
Problem: THE SPRING BRAKE CHAMBERS MOUNTED ON TAG AXLES WITH MOUNTING STUDS ALIGNED HORIZONTALLY INSTEAD OF VERTICALLY CAN RESULT IN FRACTURE OF THE BRAKE CHAMBER HOUSING BASE WHICH LIMITS THE APPLICATION OF SERVICE BRAKES ON THE AFFECTED WHEEL. Recall Details
Problem: SEAT BELT WEBBING MAY CHAFE AS THE SEAT SLIDES BACK AND FORTH. Recall Details
Problem: SEAT BELT MOUNTING BRACKET STRENGTH MAY BE BELOW REQUIREMENT OF FMVSS 209 AND COULD CRACK. Recall Details
Problem: WHEN SEAT BELTS ARE NOT BEING WORN, ABRADING OF THE WEBBING MAY OCCUR AT THE D-RING. Recall Details
Problem: FASTENERS USED TO ASSEMBLE THE D RING ANCHORAGE FOR THE SHOULDER HARNESS MAY NOT PROVIDE SUFFICIENT STRENGTH TO MEET SPECIFIED LOAD REQUIREMENTS OF FMVSS 210. Recall Details
Problem: NUTS THAT RETAIN THE WHEEL HUBS ON THE TANDEM DRIVE AXLES MAY NOT BE PROPERLY TORQUED ON THE LEFT HAND SIDE. Recall Details
Problem: WELDS JOINING THE AXLE SUPPORT BRACKET TO THE REAR DRIVE AXLE MAY BE DEFECTIVE DUE TO INSUFFICIENT COVERAGE AND/OR PENETRATION. Recall Details
Problem: SEAT BELT MOUNTING BRACKET STRENGTH MAY BE BELOW REQUIREMENT OF FMVSS 209 AND COULD CRACK. Recall Details
Problem: WELDS JOINING THE AXLE SUPPORT BRACKET TO THE REAR DRIVE AXLE MAY BE DEFECTIVE DUE TO INSUFFICIENT COVERAGE AND/OR PENETRATION. Recall Details
Problem: THE CENTRAL TUBE PART OF THE DRAG LINK, WHICH IS SET IN A ROTATIONAL POSITION, DOES NOT HAVE ENOUGH CLEARANCE BETWEEN THE NUT OR BOLT HEAD AND THE AXLE BEAM. CONSEQUENCE OF DEFECT: THERE COULD BE INTERFERENCE DURING A RIGHT TURN WHEEL CUT AND MAY CAUSE THE STEERING LINKAGE TO BIND, LEADING TO THE LOSS OF STEERING CONTROL AND AN ACCIDENT. Recall Details
Problem: FASTENERS USED TO ASSEMBLE THE D RING ANCHORAGE FOR THE SHOULDER HARNESS MAY NOT PROVIDE SUFFICIENT STRENGTH TO MEET SPECIFIED LOAD REQUIREMENTS OF FMVSS 210. Recall Details
Problem: THE CENTRAL TUBE PART OF THE DRAG LINK, WHICH IS SET IN A ROTATIONAL POSITION, DOES NOT HAVE ENOUGH CLEARANCE BETWEEN THE NUT OR BOLT HEAD AND THE AXLE BEAM. CONSEQUENCE OF DEFECT: THERE COULD BE INTERFERENCE DURING A RIGHT TURN WHEEL CUT AND MAY CAUSE THE STEERING LINKAGE TO BIND, LEADING TO THE LOSS OF STEERING CONTROL AND AN ACCIDENT. Recall Details
Problem: CRACKS CAN DEVELOP IN THE HUB IN THE INNER WHEEL BEARING AREA. CONSEQUENCE OF DEFECT: OIL LEAKS COULD OCCUR RESULTING IN LACK OF LUBRICATION. Recall Details
Problem: THE LN-2 PASSENGER SEAT MAY NOT COMPLY WITH FMVSS 207 REQUIRING THAT THE SEATBACK REMAIN IN ITS SET POSITION WHEN SUBJECTED TO A 3300 INCH POUND REARWARD FORCE. CONSEQUENCE OF DEFECT: SLIPPAGE OF THE SEATBACK MECHANISM COULD OCCUR DURING AN ACCIDENT AND POSSIBLY INJURE THE PASSENGER. Recall Details
Problem: REAR BRAKE RELAY VALVE CONTROL LINE WAS CONNECTED TO THE SECONDARY DOUBLE CHECK VALVE, RATHER THAN THE PRIMARY ONE. CONSEQUENCE OF DEFECT: THESE TRUCKS HAVE A TWO AXLE BRAKE SYSTEM EACH ON SEPARATE SYSTEMS TO AVOID TOTAL LOSS OF BRAKES. HOWEVER WITH THE MISCONNECTED LINES AND IF A RUPTURE OR LEAK OCCURS IN THE CONTROL LINE, THE FRONT AND REAR AXLE BRAKES WILL FAIL. Recall Details
Problem: THE CENTER BRACKET, ONE OF THE THREE USED TO HOLD THE GRAB HANDLE IN PLACE, CONTAINS A RIVET WHICH MAY NOT BE PROPERLY ALIGN. THIS ALLOWS A SMALL GAP TO EXIST BETWEEN THE RIVET HEAD AND THE BRACKET. CONSEQUENCE OF DEFECT: A RING ON A FINGER COULD BE CAUGHT IN THE GAP AND RESULT IN PERSONAL INJURY TO A PERSON GETTING OUT OR INTO THE CAB. Recall Details
Problem: REAR BRAKE RELAY VALVE CONTROL LINE WAS CONNECTED TO THE SECONDARY DOUBLE CHECK VALVE, RATHER THAN THE PRIMARY ONE. CONSEQUENCE OF DEFECT: THESE TRUCKS HAVE A TWO AXLE BRAKE SYSTEM EACH ON SEPARATE SYSTEMS TO AVOID TOTAL LOSS OF BRAKES. HOWEVER WITH THE MISCONNECTED LINES AND IF A RUPTURE OR LEAK OCCURS IN THE CONTROL LINE, THE FRONT AND REAR AXLE BRAKES WILL FAIL. Recall Details
Problem: THE CENTER BRACKET, ONE OF THE THREE USED TO HOLD THE GRAB HANDLE IN PLACE, CONTAINS A RIVET WHICH MAY NOT BE PROPERLY ALIGN. THIS ALLOWS A SMALL GAP TO EXIST BETWEEN THE RIVET HEAD AND THE BRACKET. CONSEQUENCE OF DEFECT: A RING ON A FINGER COULD BE CAUGHT IN THE GAP AND RESULT IN PERSONAL INJURY TO A PERSON GETTING OUT OR INTO THE CAB. Recall Details
Problem: CRACKS CAN DEVELOP IN THE HUB IN THE INNER WHEEL BEARING AREA. CONSEQUENCE OF DEFECT: OIL LEAKS COULD OCCUR RESULTING IN LACK OF LUBRICATION. Recall Details
Problem: A BOLT MAY NOT HAVE BEEN FULLY TIGHTENED ON THE PITMAN ARM AND RETAINING SCREWS MAY NOT HAVE BEEN INSTALLED OR MAY NOT HAVE BEEN FULLY TIGHTENED. THE PITMAN ARM COULD SEPARATE FROM THE STEERING SHAFT. Recall Details
Problem: ENGINE COOLING FAN IS MADE OF A PLASTIC OUTER RING AND BLADE MOLDED TO A METAL CENTER. THE FAN BLADES CAN SEPARATE FROM THE HUB AND DISINTEGRATE WITHOUT WARNING. Recall Details
Problem: THE TIE ROD END ATTACHES TO THE STEERING LINKAGE WITH A STUD WHICH MAY CRACK AND BREAK. Recall Details
Problem: A POORLY DESIGNED BRACKET WHICH MOUNTS THE SERVICE/PARKING BRAKE UNIT TO THE REAR DRIVE AXLE MAY ALLOW DAMAGE TO BRAKE CHAMBER. DAMAGE MAY CAUSE THE SPRING BRAKE TO BE APPLIED. Recall Details
Problem: A POORLY DESIGNED BRACKET WHICH MOUNTS THE SERVICE/PARKING BRAKE UNIT TO THE REAR DRIVE AXLE MAY ALLOW DAMAGE TO BRAKE CHAMBER. DAMAGE MAY CAUSE THE SPRING BRAKE TO BE APPLIED. Recall Details
Problem: A BOLT MAY NOT HAVE BEEN FULLY TIGHTENED ON THE PITMAN ARM AND RETAINING SCREWS MAY NOT HAVE BEEN INSTALLED OR MAY NOT HAVE BEEN FULLY TIGHTENED. THE PITMAN ARM COULD SEPARATE FROM THE STEERING SHAFT. Recall Details
Problem: REAR BRAKE RELAY VALVE CONTROL LINE WAS CONNECTED TO THE SECONDARY DOUBLE CHECK VALVE, RATHER THAN THE PRIMARY ONE. CONSEQUENCE OF DEFECT: THESE TRUCKS HAVE A TWO AXLE BRAKE SYSTEM EACH ON SEPARATE SYSTEMS TO AVOID TOTAL LOSS OF BRAKES. HOWEVER WITH THE MISCONNECTED LINES AND IF A RUPTURE OR LEAK OCCURS IN THE CONTROL LINE, THE FRONT AND REAR AXLE BRAKES WILL FAIL. Recall Details
Problem: ENGINE COOLING FAN IS MADE OF A PLASTIC OUTER RING AND BLADE MOLDED TO A METAL CENTER. THE FAN BLADES CAN SEPARATE FROM THE HUB AND DISINTEGRATE WITHOUT WARNING. Recall Details
Problem: A POORLY DESIGNED BRACKET WHICH MOUNTS THE SERVICE/PARKING BRAKE UNIT TO THE REAR DRIVE AXLE MAY ALLOW DAMAGE TO BRAKE CHAMBER. DAMAGE MAY CAUSE THE SPRING BRAKE TO BE APPLIED. Recall Details
Problem: SOME OF THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS". THE RELEASE TIME FOR THE REAR BRAKES MAY EXCEED THE .55 SECOND LIMIT REQUIREMENT FOR SAFE BRAKING. Recall Details
Problem: A BOLT MAY NOT HAVE BEEN FULLY TIGHTENED ON THE PITMAN ARM AND RETAINING SCREWS MAY NOT HAVE BEEN INSTALLED OR MAY NOT HAVE BEEN FULLY TIGHTENED. THE PITMAN ARM COULD SEPARATE FROM THE STEERING SHAFT. Recall Details
Problem: A BOLT MAY NOT HAVE BEEN FULLY TIGHTENED ON THE PITMAN ARM AND RETAINING SCREWS MAY NOT HAVE BEEN INSTALLED OR MAY NOT HAVE BEEN FULLY TIGHTENED. THE PITMAN ARM COULD SEPARATE FROM THE STEERING SHAFT. Recall Details
Problem: A POORLY DESIGNED BRACKET WHICH MOUNTS THE SERVICE/PARKING BRAKE UNIT TO THE REAR DRIVE AXLE MAY ALLOW DAMAGE TO BRAKE CHAMBER. DAMAGE MAY CAUSE THE SPRING BRAKE TO BE APPLIED. Recall Details
Problem: PROTECTIVE SLEEVES THAT COVER THE LAP BELTS IN THE AREA OF SEAT CUSHION SUPPORT PAN WERE OMITTED. SEAT BELTS MAY FAIL DURING A COLLISION. BELTS ARE NOT IN COMPLIANCE WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, "SEATING SYSTEMS". Recall Details
Problem: BRAKES MAY FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS". THE AIR BRAKES ON THE FRONT AXLE MAY NOT ACTUATE AND RELEASE WITHIN THE TIME REQUIRED FOR SAFE BRAKING. THE BRAKES MAY EXCEED THE .55 SECOND LIMITS. Recall Details
Problem: THE ALUMINUM WHEEL HUBS DEVELOP CRACKS NEAR THE INNER WHEEL BEARING, ALLOWING LOSS OF BEARING LUBRICANT. CONSEQUENCE OF DEFECT: THE HUB FAILURE AND/OR LOSS OF BEARING LUBRICANT RESULTING IN BEARING FREEZE UP COULD RESULT IN STEERING CONTROL PROBLEMS, WHICH MAY LEAD TO AN ACCIDENT. Recall Details
Problem: ON THE INVOLVED VEHICLES, BOTH THE AIR BRAKE HOSE CONNECTIONS AND THE AIR PRESSURE GAUGES FOR THE DUEL BRAKE FEATURE MAY HAVE BEEN CONNECTED IN REVERSE ORDER. INCORRECTLY CONNECTED BRAKE HOSES IN COMBINATION WITH AN AIR LEAK IN EITHER THE PRIMARY OR SECONDARY BRAKE SYSTEMS COULD CAUSE BRAKE FAILURE ON ONE OR MORE AXLES. Recall Details
Problem: THE SAFETY CHAIN BALE PORTION OF THE TOWING ATTACHMENT MAY HAVE A DEFECTIVE WELD IN A CRITICAL AREA. IF THE TRAILER HITCH SHOULD BECOME UNLATCHED OR IN THE EVENT OF AN ACCIDENT CAUSING THE TRUCK AND TRAILER TO BECOME SEPARATED, THE RESULTING FORCES COULD CAUSE A FAILURE OF THE SAFETY CHAIN BALE. A FAILURE OF THIS PART WOULD ALLOW COMPLETE SEPARATION OF THE TRUCK AND TRAILER WITHOUT PRIOR WARNING. Recall Details
Problem: THE FOUR BOLTS USED TO ATTACH EACH FUEL TANK SUPPORT BRACKET TO THE FRAME CONTAIN "QUENCH CRACKS" DUE TO IMPROPER HEAT TREATMENT IN THE MANUFACTURING PROCESS. THESE DEFECTIVE BOLTS COULD GIVE WAY, ALLOWING THE FUEL TANK TO BECOME DISLODGED FROM THE BRACKET OR THE BRACKET FROM THE FRAME. Recall Details
Problem: THE KNUCKLE STOP NUTS ARE TOO SHORT, POSSIBLY RESULTING IN FAILURE OF THE NUT UNDER HEAVY STEERING FORCE. THIS MAY ALLOW THE WHEEL TO ROTATE TOO FAR TO THE RIGHT OR LEFT, PERMITTING THE TIRE TO CONTACT OTHER VEHICLE PARTS. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: THE ALUMINUM WHEEL HUBS DEVELOP CRACKS NEAR THE INNER WHEEL BEARING, ALLOWING LOSS OF BEARING LUBRICANT. CONSEQUENCE OF DEFECT: THE HUB FAILURE AND/OR LOSS OF BEARING LUBRICANT RESULTING IN BEARING FREEZE UP COULD RESULT IN STEERING CONTROL PROBLEMS, WHICH MAY LEAD TO AN ACCIDENT. Recall Details
Problem: ON CERTAIN VEHICLES, SOME COTTER PINS MAY BE MISSING AT THE BALL JOINT CONNECTIONS OF THE DRAG LINK ENDS AND TIE ROD ENDS IN THE LOWER FRONT AXLE STEERING SYSTEM. STEERING JOINT COULD SEPARATE IF THE BALL STUD RETAINING NUT LOOSENS AND FALLS OFF DUE TO ABSENCE OF COTTER PIN. Recall Details
Problem: THE SAFETY CHAIN BALE PORTION OF THE TOWING ATTACHMENT MAY HAVE A DEFECTIVE WELD IN A CRITICAL AREA. IF THE TRAILER HITCH SHOULD BECOME UNLATCHED OR IN THE EVENT OF AN ACCIDENT CAUSING THE TRUCK AND TRAILER TO BECOME SEPARATED, THE RESULTING FORCES COULD CAUSE A FAILURE OF THE SAFETY CHAIN BALE. A FAILURE OF THIS PART WOULD ALLOW COMPLETE SEPARATION OF THE TRUCK AND TRAILER WITHOUT PRIOR WARNING. Recall Details
Problem: BRAKES MAY FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS". THE AIR BRAKES ON THE FRONT AXLE MAY NOT ACTUATE AND RELEASE WITHIN THE TIME REQUIRED FOR SAFE BRAKING. THE BRAKES MAY EXCEED THE .55 SECOND LIMITS. Recall Details
Problem: A BOLT MAY NOT HAVE BEEN FULLY TIGHTENED ON THE PITMAN ARM AND RETAINING SCREWS MAY NOT HAVE BEEN INSTALLED OR MAY NOT HAVE BEEN FULLY TIGHTENED. THE PITMAN ARM COULD SEPARATE FROM THE STEERING SHAFT. Recall Details
Problem: BRAKES MAY FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS". THE AIR BRAKES ON THE FRONT AXLE MAY NOT ACTUATE AND RELEASE WITHIN THE TIME REQUIRED FOR SAFE BRAKING. THE BRAKES MAY EXCEED THE .55 SECOND LIMITS. Recall Details
Problem: A BOLT MAY NOT HAVE BEEN FULLY TIGHTENED ON THE PITMAN ARM AND RETAINING SCREWS MAY NOT HAVE BEEN INSTALLED OR MAY NOT HAVE BEEN FULLY TIGHTENED. THE PITMAN ARM COULD SEPARATE FROM THE STEERING SHAFT. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: ON SOME VEHICLES, THE LOWER STEERING DRIVE SHAFT RUBS AGAINST THE STEERING BOOT RETAINER SPRING. THIS CHAFING CAN WEAR A GROOVE INTO THE DRIVE SHAFT WHICH CAN EVENTUALLY LEAD TO A SEPARATION OF THE TUBE. Recall Details
Problem: THE SAFETY CHAIN BALE PORTION OF THE TOWING ATTACHMENT MAY HAVE A DEFECTIVE WELD IN A CRITICAL AREA. IF THE TRAILER HITCH SHOULD BECOME UNLATCHED OR IN THE EVENT OF AN ACCIDENT CAUSING THE TRUCK AND TRAILER TO BECOME SEPARATED, THE RESULTING FORCES COULD CAUSE A FAILURE OF THE SAFETY CHAIN BALE. A FAILURE OF THIS PART WOULD ALLOW COMPLETE SEPARATION OF THE TRUCK AND TRAILER WITHOUT PRIOR WARNING. Recall Details
Problem: ON CERTAIN VEHICLES, THE LENGTH OF THREAD ENGAGEMENT IN THE GARRISON POWER STEERING DRAG LINK IS LESS THAN THAT SPECIFIED FOR THIS INSTALLATION. Recall Details
Problem: ON SOME VEHICLES, THE LOWER STEERING DRIVE SHAFT RUBS AGAINST THE STEERING BOOT RETAINER SPRING. THIS CHAFING CAN WEAR A GROOVE INTO THE DRIVE SHAFT WHICH CAN EVENTUALLY LEAD TO A SEPARATION OF THE TUBE. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: BRAKES MAY FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS". THE AIR BRAKES ON THE FRONT AXLE MAY NOT ACTUATE AND RELEASE WITHIN THE TIME REQUIRED FOR SAFE BRAKING. THE BRAKES MAY EXCEED THE .55 SECOND LIMITS. Recall Details
Problem: THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS". THE BRAKE DRUMS DO NOT MEET WITH BRAKE RECOVERY REQUIREMENTS. BRAKES MAY BE NOT PERFORM ADEQUATELY ON LONG DOWNGRADES OR DUE TO HEAVY APPLICATIONS OF AIR WHEN THE VEHICLE IS BROUGHT TO A STOP FROM HIGH SPEEDS. Recall Details
Problem: THE CHECK VALVE, LOCATED ON THE INLET SIDE OF THE PRIMARY AND SECONDARY AIR TANKS MAY CRACK IN THE FEMALE FITTING AREA AND CAUSE A SLOW LOSS OF AIR. A LEAKING VALVE WILL REDUCE AIR PRESSURE AND PARTIAL OR COMPLETE LOSS OF BRAKES ON THOSE AXLES THAT DEPEND UPON THAT PART OF THE SYSTEM COULD OCCUR. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: ON THE INVOLVED VEHICLES, CRACKS MAY DEVELOP AT THE BASE OF THE INNER WHEEL BEARING CUP AND PROPAGATE CIRCUMFERENTIALLY AROUND THE BARREL OF THE HUB. A FRACTURE BETWEEN THE INNER HUB END AND THE FLANGE PORTION OF THE HUB COULD EVENTUALLY DEVELOP. FAILURE COULD OCCUR CAUSING HUB SEPARATION. CONTINUED OPERATION AFTER HUB SEPARATION HAS OCCURRED COULD RESULT IN LOCK-UP OF BRAKE ASSEMBLY, EXCESSIVE HEAT GENERATION DUE TO BRAKE LINING TO DRUM CONTACT, AND PROGRESSIVE DAMAGE TO THE HUB, CAUSING THE SEPARATED HUB WITH THE WHEEL AND TIRE TO DISENGAGE FROM THE TRUCK. Recall Details
Problem: ON THE INVOLVED VEHICLES, THE PINCH BOLT THAT CLAMPS THE STEERING SHAFT YOKE TO THE INPUT SHAFT ON THE GEARING BOX MAY BE LOOSE. THE SPLINED SURFACES ON THE YOKE AND SHAFT COULD WEAR AS A RESULT. CONTINUED USAGE COULD CAUSE SEVERE WEAR AND EVENTUAL SLIPPAGE OF THE JOINT. Recall Details
Problem: THE CHECK VALVE, LOCATED ON THE INLET SIDE OF THE PRIMARY AND SECONDARY AIR TANKS MAY CRACK IN THE FEMALE FITTING AREA AND CAUSE A SLOW LOSS OF AIR. A LEAKING VALVE WILL REDUCE AIR PRESSURE AND PARTIAL OR COMPLETE LOSS OF BRAKES ON THOSE AXLES THAT DEPEND UPON THAT PART OF THE SYSTEM COULD OCCUR. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: ON THE INVOLVED VEHICLES, THE PINCH BOLT THAT CLAMPS THE STEERING SHAFT YOKE TO THE INPUT SHAFT ON THE GEARING BOX MAY BE LOOSE. THE SPLINED SURFACES ON THE YOKE AND SHAFT COULD WEAR AS A RESULT. CONTINUED USAGE COULD CAUSE SEVERE WEAR AND EVENTUAL SLIPPAGE OF THE JOINT. Recall Details
Problem: ON THE INVOLVED VEHICLES, CRACKS MAY DEVELOP AT THE BASE OF THE INNER WHEEL BEARING CUP AND PROPAGATE CIRCUMFERENTIALLY AROUND THE BARREL OF THE HUB. A FRACTURE BETWEEN THE INNER HUB END AND THE FLANGE PORTION OF THE HUB COULD EVENTUALLY DEVELOP. FAILURE COULD OCCUR CAUSING HUB SEPARATION. CONTINUED OPERATION AFTER HUB SEPARATION HAS OCCURRED COULD RESULT IN LOCK-UP OF BRAKE ASSEMBLY, EXCESSIVE HEAT GENERATION DUE TO BRAKE LINING TO DRUM CONTACT, AND PROGRESSIVE DAMAGE TO THE HUB, CAUSING THE SEPARATED HUB WITH THE WHEEL AND TIRE TO DISENGAGE FROM THE TRUCK. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: AN OPERATIONAL AMPLIFIER IN THE AXLE CONTROLLERS ON THE INVOLVED VEHICLES MAY DEVIATE FROM SPECIFICATIONS. THERE MAY ALSO BE AN OPENING IN A SOLDER CONNECTION BETWEEN THE PRINTED CIRCUIT BOARD AND THE NEGATIVE TERMINAL OF THE CAPACITOR. THESE CONDITIONS CAUSE THE ANTI-LOCK VALVE SOLENOID TO BE ENERGIZED CONTINUOUSLY. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: CRACKS MAY DEVELOP IN THE TRUCK"S REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
Problem: THE INVOLVED VEHICLES CONTAIN DEFECTIVE BALL STUDS THAT WERE IMPROPERLY HEAT-TREATED AND THUS CONTAIN CRACKS. THESE STUDS, LOCATED IN THE PITMAN ARM, COULD EVENTUALLY FRACTURE IN THE THREADED PORTION UNDER THE RETAINING NUT. Recall Details
|