2019 JEEP WRANGLER Complaints

2019 Jeep Wrangler JLU experienced intermittent CAN-C communication failure. Vehicle has repeatedly experienced simultaneous loss of multiple electronic systems. On September 7th 2026, while driving, vehicle unexpectedly lost electric power steering, windshield wipers activated without command, ABS/TPMS/ESC warning lights illuminated, and vehicle subsequently would not shift into gear after stopping at a traffic light. Hazard lights would not activate. After shutting vehicle off, vehicle would not enter ACC or restart normally. Opening driver’s door unexpectedly caused vehicle to enter ACC. Manipulating the CAN-bus wiring/STAR connector behind the glove box has historically temporarily restored normal operation. Vehicle has previously required repair to this wiring/connector, and the failure has recurred. This has been occurring for at least 3 years and since 60,000 miles. This presents a significant safety hazard because steering assistance, shifting/propulsion, and signaling were simultaneously affected while driving. It is a known Chrysler issue (FCA STAR Case S2108000146) and should be recalled as there is a CLEAR and present danger with this ongoing issue.

Getting the well know Jeep "Death Wobble". Was advised by Carvana when I bought this vehicle that it had an open recall for this exact issue (Manufacturer Recall Number CDJR XF1) due to the Steering Damper having air in it. However, when I contacted a Jeep dealership to get it fixed, I was told there is no recall for the Steering Damper for my specific vehicle. When I look it up on NHTSA, there isn't a recall listed on here either. Whenever I hit transitions in the pavement while driving above 50mph, I get the death wobble on the front of the vehicle. I have not yet had it repaired, but I plan to do so regardless of whether a recall exists. This is clearly an affected vehicle that was wrongly excluded from the manufacturer's recall for the Steering Damper on vehicles manufactured prior to August 11, 2020. My vehicle was manufactured in April 2019, so it is definitely in the correct date range, and with the exact same issue of others that were recalled. The only reason I have not crashed is because I've taken EVOC classes (for driving firetrucks and ambulances), and I am able to control it when it does happen. There were approximately 65k miles on the vehicle when I bought it, and there is about 72k miles now. It has been happening since I bought it in December 2025 from Carvana.

The IPC Cluster completely blank. Unsafe to operate vehicle, as speed was unknown, unable to read fuel gauges, and unable to see any warning lights. Experienced the exact problem noted in Recall Campaign 30B/NHTSA 24-V 652 for jeeps with the 3.5 inch cluster layout, and my VIN is not listed on the recall list.

Check engine, ABS, Service Shifter suddenly pops up and the steering was hard to turn almost had an accident

The IPC Cluster stopped working and the screen is completely blank. It is unsafe to drive since I don’t know how fast I’m going, how much gas is in the tank, and inability to see any warning lights. The recall for this is Recall Campaign 30B/NHTSA 24-V 652 for jeeps with the 3.5 inch cluster layout, which I have but my VIN is not listed on the recall list. It should be!

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the instrument panel was blank. The vehicle was taken to the dealer and was diagnosed with instrument cluster failure. The contact was informed that the instrument cluster needed to be replaced. The vehicle was awaiting the repair. The manufacturer was notified of the failure and referenced NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The failure mileage was unknown.

ABS pump and module combination is making brake calipers to not released. It’s been two times in 6 months my brakes are used up and calipers locked. Jeep knows this issue across its brand of vehicles but not called for a recall. Parts are also in back order that says lot of vehicles has issues. Confirmed with local dealership.

The 3.5-inch Instrument Panel Cluster went completely black while operating the vehicle, causing a total loss of speedometer and critical safety indicators (violating FMVSS 101). Concurrently, the engine computer limited vehicle performance to 3,000 RPM (limp mode). The vehicle exhibits the exact failure mode detailed in NHTSA Campaign 24V-652 (Jeep Recall 30B), but the manufacturer has not yet added this VIN to the recall population.

VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an ignition source well above its auto-ignition point. 2. COMPONENT DEGRADATION: Rubber lines near the engine outlet appear susceptible to heat-fatigue failure under high ambient/high load conditions, posing a sudden fire hazard at highway speeds. REPAIR: Roadside trim/re-clamp of the split hose allowed temporary transit. Replacing full hose assembly (68280797AC), upgrading radiator lines, and performing a full OAT coolant flush/vacuum refill. No oil contamination was noted after the incident.

The vehicle is experiencing severe, premature galvanic corrosion on the doors, hinges, and hood due to a documented factory defect where aluminum panels press directly against steel hinges without proper isolation (acknowledged by the manufacturer in TSB 31-001-24).This is a critical structural and safety hazard covered under Federal Motor Vehicle Safety Standard (FMVSS) 206, which regulates door locks and door retention components. The advanced sub-surface corrosion is causing the metal surrounding the door hinges to degrade and oxidize, causing the paint to blister, bubble, and flake off. Over time, this structural failure poses an imminent safety risk of causing the door hinges to seize or bind, potentially jamming the doors shut during an emergency and trapping occupants inside the vehicle. Furthermore, the degradation of these hinge components creates a severe risk of the doors failing and opening unexpectedly while the vehicle is in motion at highway speeds.The manufacturer is refusing to address this structural defect because the vehicle passed its 5-year calendar warranty window, ignoring the fact that this sub-surface chemical reaction takes years to visibly manifest. This defect requires a formal safety investigation and an expanded recall to protect drivers from door-retention failures.